DRIFIRE Flight Suit

Compare DRIFIRE flight suits, jacket and pant separates, and mid-layer pieces side by side. The selection covers one-piece and two-piece suits plus men’s and women’s fits, so you can match coverage and fit to your crew.

New DRIFIRE flight suit options to compare

One-piece DRIFIRE FORTREX flight suit displayed full length on a headless mannequin in a studio

DRIFIRE® FORTREX® 1-Piece Flight Suit (NAVAIR) — continuous FR-L4 coverage for flight crews

Rated FR-L4 and designated for NAVAIR use, this one-piece suit gives continuous coverage from collar to cuff with no waist gap to ride up in the seat. Inherently flame-resistant fabric works with moisture-wicking, fast-drying fibers that pull sweat off skin and help hold temperature steady through long cockpit shifts.
Two-piece DRIFIRE Fortrex flight suit jacket and matching pant shown together on a headless mannequin

DRIFIRE - Fortrex 2-Piece Flight Suit (NAVAIR) for Navy and USMC flight crews

Built as a two-piece set for Navy flight crews, the jacket and pant separate when you need to vent or change after a run. The design emphasizes durability and permanent flame resistance, while superior moisture wicking and fast drying move sweat away so your skin temperature stays regulated through the shift.
DRIFIRE FORTREX flight suit jacket displayed on a torso mannequin against a grey studio backdrop

DRIFIRE® FORTREX® Flight Suit Jacket (NAVAIR) — FR-L4 torso layer for crews already covered below

Carrying the NAVAIR designation and an FR-L4 rating, the jacket-only option protects the torso when your lower body is already covered or you want less bulk. It brings inherently flame-resistant construction and fast-drying moisture management to the upper layer, which helps keep you drier moving between the aircraft, the line and the briefing room.
DRIFIRE FORTREX V2 flight suit jacket shown on a torso mannequin under bright studio lighting

DRIFIRE® FORTREX® V2 Flight Suit Jacket — updated FR-L4 cut with flash fire and arc flash protection

The V2 jacket is the current iteration of the FORTREX flight suit top, rated FR-L4 for dual-hazard protection against flash fire and arc flash. It keeps the inherently flame-resistant fabric and moisture-wicking comfort of the line while updating the cut, so protective performance moves like athletic wear rather than stiff coveralls.
DRIFIRE FORTREX women's flight suit jacket displayed on a dress form against a neutral studio backdrop
Built for aircrew

DRIFIRE® FORTREX® Women's Flight Suit Jacket (NAVAIR) — women's FR-L4 cut for flight crews

Rated FR-L4 and built to NAVAIR requirements, this women’s flight suit jacket is drafted through the torso and shoulder so coverage stays consistent when you reach for overhead controls or kneel on the flight line. Inherently flame-resistant fabric pairs with moisture-wicking, fast-drying fibers that regulate skin temperature through long, hot shifts in the aircraft.
Field-proven picks

Popular DRIFIRE flight suit separates and layers

DRIFIRE FORTREX V2 women's flight suit jacket displayed on a women's-cut torso mannequin

DRIFIRE® FORTREX® V2 Women's Flight Suit Jacket — V2 women's cut with FR-L4 dual-hazard protection

The V2 women’s jacket gives crews who preferred the original women’s cut an updated option with the same FR-L4 protection and dual-hazard coverage against flash fire and arc flash. The shaped pattern limits riding up at the waist, and fast-drying fibers help the garment recover between back-to-back duty days.
DRIFIRE FORTREX women's flight suit pant displayed on a mannequin lower body in a studio

DRIFIRE® FORTREX® Women's Flight Suit Pant (NAVAIR) — women's FR-L4 lower half for matched kits

This women’s flight suit pant carries the NAVAIR designation and an FR-L4 rating, covering the lower body as part of a matched kit or on its own. Inherent flame resistance stays in the fiber rather than a coating, and moisture-wicking performance keeps legs drier when you are on your feet for the whole shift.
DRIFIRE FORTREX V2 women's flight suit pant shown on a mannequin against a neutral backdrop

DRIFIRE® FORTREX® V2 Women's Flight Suit Pant — V2 women's pant with FR-L4 flash fire coverage

The V2 women’s pant updates the fit of the FORTREX lower half while holding the FR-L4 protection rating. Seated work, climbing and kneeling stress the same points, so the revised cut matters as much as the fabric; either way you keep flash fire and arc flash coverage with fast-drying comfort.
DRIFIRE FORTREX flight suit pant displayed on a mannequin lower body against a grey studio wall

DRIFIRE® FORTREX® Flight Suit Pant (NAVAIR) — standard FR-L4 pant for matched FORTREX jacket kits

Standard-size crews get FR-L4 lower-body coverage with the NAVAIR designation on this FORTREX pant. It pairs with any FORTREX jacket for a matched kit, and the inherently flame-resistant, moisture-wicking fabric handles heat and sweat without relying on a chemical treatment that could wash out over time.
DRIFIRE FORTREX V2 flight suit pant displayed on a mannequin lower body under studio light

DRIFIRE® FORTREX® V2 Flight Suit Pant — updated FR-L4 lower half with fast-drying comfort

The V2 pant is the updated FORTREX lower half, rated FR-L4 for dual-hazard protection. Choose it when you want the newer pattern with the same inherently flame-resistant fabric and moisture management, then match it to a V2 jacket for a consistent fit through the waist and leg.

DRIFIRE® FORTREX® Flight Suit Mid-Layer Hoodie — FR-L4 base layer that sits flat under the suit

The mid-layer hoodie sits under your flight suit without adding bulk, so layering never costs you protection. Its inherently flame-resistant fabric carries dual-hazard coverage against flash fire and arc flash. Moisture-wicking, fast-drying fibers move sweat off skin and regulate temperature in confined cockpits, while a smooth athletic fit reduces bunching where gear rubs.

Where these flight suits work

Navy flight crews

Two flight crew members in flight suits walking across a tarmac toward a parked jet
Aircrews need coverage that stays put in the seat and dries fast between runs on the line.

Utility line work

Line crew member in a two-piece flight suit venting the jacket beside ground equipment on a hot apron
Ground and line crews benefit from separates they can vent during hot outdoor shifts.

Industrial crews

Industrial worker in a flame-resistant jacket, pant and mid-layer reviewing work orders in a plant
Industrial teams layer jacket, pant and mid-piece to match changing hazards on the job.

Safety procurement

Safety manager inspecting hanging flight suit garments on a rack in a supply room
Buyers compare fit lines and ratings to standardize issue across a whole workforce.
Choosing your fit

Compare coverage, fit and protection level

Start with coverage: a one-piece suit suits cockpit work, while a two-piece set lets you vent or change pieces separately. Then match the fit line and FR rating to your crew’s requirements.

One-piece versus two-piece coverage

A one-piece suit closes the gap at the waist and stays put when you bend into the seat. Two pieces separate for quick changes and easier laundering, which matters on rotating shifts.

Men's and women's fit lines

The women’s line is cut through the torso, hips and legs rather than scaled down from a men’s pattern, so coverage stays consistent when you reach, squat or kneel on the flight line.

Protection rating and layering

Every FORTREX piece here is rated FR-L4. Check what your operation already covers before adding a jacket, pant or mid-layer so you get full protection without excess bulk in the cockpit.
Find your direction

Three ways to narrow this flight suit range

This category holds three directions: one-piece suits for continuous coverage, two-piece jacket and pant sets you can vent or change, and mid-layer pieces that add warmth without bulk. Match each to your shift.

One-piece coverage

A single suit closes the waist gap and stays put when you bend into the seat on a long flight.

Two-piece separates

Jacket and pant split so you can vent heat, change one piece, or launder the parts separately.

Mid-layer pieces

A fitted hoodie adds warmth under the suit without stacking bulk at the arms or torso.

What buyers say about outfitting crews

These first-person notes cover ordering FR suits, comparing fits and wearing the gear through long shifts. They describe fit decisions, layering and comfort so you can weigh the same trade-offs for your own crew.
I compared one-piece and two-piece options for my crew and went with separates. Being able to vent and change pieces made the call easy on our hot line shifts.
Decorative customer review avatar icon 1
M. Alvarez
Sizing worried me most. I checked the fit line against a jacket I own, and coverage held when I reached overhead without the waist riding up.
Decorative customer review avatar icon 2
D. Whitfield
Layering took some trial and error. Starting with a thin mid-layer kept me warm at altitude, and I still had room to move once I added the outer shell.
Decorative customer review avatar icon 3
R. Kaminski
Shopper in a plain shirt checking the fit of a navy flight suit jacket in front of a fitting-room mirror
Our buyers standardised on one rating across the whole issue. Having a single protection class simplified the order and made fit checks much faster.
Decorative customer review avatar icon 4
T. Boone
I ordered for a rotating shift pattern and needed gear that dried between runs. The fabric wicked sweat fast, so I stopped feeling damp during back-to-back duty days.
Decorative customer review avatar icon 5
J. Prieto
Comparing coverage side by side helped me see why the two-piece suited our ground crew better than a single suit for hot outdoor work.
Decorative customer review avatar icon 6
A. Mendez

Questions before you order

Fit, sizing, protection rating and layering all affect whether a flight suit works on your crew. These answers cover the trade-offs that come up most often when buyers compare options in this category.

Shopper comparing the sleeve fabric of a navy flight suit jacket against a fabric swatch
Shopper holding a navy flight suit jacket open to check fit across the shoulders in a fitting room
Pick the one-piece when you want continuous coverage with no waist gap and a single item to issue. The two-piece is easier to vent, change and launder in parts, and it suits crews who move between the aircraft and facility work during a shift.
The women’s FORTREX pieces are drafted through the torso, hips and leg rather than scaled from a men’s pattern. If a men’s suit bunches at the waist or pulls across the seat, the women’s cut usually holds coverage better when you reach or kneel.
FR-L4 is the protection classification these DRIFIRE flight suit pieces carry. Use it to confirm the garment matches your operation’s requirement, then check that whatever you layer with it keeps you within that same standard.
The pieces share the FORTREX name and FR-L4 rating, but patterns differ between the original and V2 lines. Match the same line on top and bottom for a consistent fit, and confirm sizing with your distributor before mixing generations.
A mid-layer hoodie built for under-suit wear is cut to sit flat and avoid bulk at the arms and torso. If you run warm or work in a confined cockpit, start with the hoodie alone and add outer layers only when conditions call for them.
Moisture-wicking, fast-drying fibers in these pieces move sweat off the skin, which helps regulate temperature. A base layer plus one outer shell usually covers most conditions; add coverage only where your hazard assessment requires it.
More from the field

Continue with related FR gear guidance

The posts below continue past this page with fit, layering and protection detail from the same DRIFIRE line. Use them to check how a suit behaves over a full shift before you settle on a coverage style.
Worker wearing dark flame-resistant work pants on an industrial plant floor

DRIFIRE Pants

Compare DRIFIRE FR pants by protection rating, cut and fabric weight, from daily utility styles through tactical combat and field builds. Each option below suits a different kind of shift.

Row of DRIFIRE FR flame resistant work shirts hanging on a steel rail in an industrial locker room

DRIFIRE FR Shirts

This category gathers DRIFIRE FR shirts for industrial and utility work, from lightweight base layers to hi-vis utility shirts. Compare sleeve length, arc rating, weight and certifications to match a shirt to your shift.

Camouflage FR combat shirt laid flat on a dark workbench

DRIFIRE Combat Shirt

Compare DRIFIRE combat shirts by camouflage pattern, sizing, sleeve cut and FR fabric so you can match the right garment to your mission, uniform allowance or worksite requirement.

A pair of dark flame-resistant tactical combat pants laid flat on a steel workbench in an industrial gear room

DRIFIRE Combat Pants

This category gathers DRIFIRE combat pants for men and women, from FR tactical and cargo cuts to camo field pairs. Compare protection level, fit, condition and listed price side by side, then narrow the choice to the pant that fits your hazard, your shift and your budget.